Smokeping_probes_FPing6(3) SmokePing Smokeping_probes_FPing6(3)
NAME
Smokeping::probes::FPing6 - FPing6 Probe for SmokePing
SYNOPSIS
*** Probes ***
+FPing6
binary = /opt/local/bin/fping6 # mandatory
blazemode = true
hostinterval = 1.5
interface = eth0
mininterval = 0.001
offset = 50%
packetsize = 5000
pings = 20
protocol = 6
sourceaddress = ::1
step = 300
timeout = 1.5
tos = 0x20
usestdout = true
# The following variables can be overridden in each target section
/^influx_.+/ = influx_location = In the basement
# [...]
*** Targets ***
probe = FPing6 # if this should be the default probe
# [...]
+ mytarget
# probe = FPing6 # if the default probe is something else
host = my.host
/^influx_.+/ = influx_location = In the basement
DESCRIPTION
Integrates FPing6 as a probe into smokeping. This probe is derived from
FPing; the only difference is that the target host used for checking
the fping command output is ::1 instead of localhost.
VARIABLES
Supported probe-specific variables:
binary
The location of your fping binary.
Example value: /opt/local/bin/fping6
This setting is mandatory.
blazemode
Send an extra ping and then discard the first answer since the
first is bound to be an outlier.
Example value: true
hostinterval
The fping "-p" parameter, but in (possibly fractional) seconds
rather than milliseconds, for consistency with other Smokeping
probes. From fping(1):
This parameter sets the time that fping waits between successive
packets to an individual target.
Example value: 1.5
interface
The name of the network interface to perform the ping on.
Example value: eth0
mininterval
The fping "-i" parameter, but in (probably fractional) seconds
rather than milliseconds, for consistency with other Smokeping
probes. From fping(1):
The minimum amount of time between sending a ping packet to any
target.
Example value: 0.001
Default value: 0.01
offset
If you run many probes concurrently you may want to prevent them
from hitting your network all at the same time. Using the probe-
specific offset parameter you can change the point in time when
each probe will be run. Offset is specified in % of total interval,
or alternatively as 'random', and the offset from the 'General'
section is used if nothing is specified here. Note that this does
NOT influence the rrds itself, it is just a matter of when data
acquisition is initiated. (This variable is only applicable if the
variable 'concurrentprobes' is set in the 'General' section.)
Example value: 50%
packetsize
The ping packet size (in the range of 12-64000 bytes).
Example value: 5000
pings
How many pings should be sent to each target, if different from the
global value specified in the Database section. Note that the
number of pings in the RRD files is fixed when they are originally
generated, and if you change this parameter afterwards, you'll have
to delete the old RRD files or somehow convert them.
Example value: 20
protocol
Choose if the ping should use IPv4 or IPv6.
Example value: 6
Default value: 6
sourceaddress
The fping "-S" parameter . From fping(1):
Set source address.
Example value: ::1
step
Duration of the base interval that this probe should use, if
different from the one specified in the 'Database' section. Note
that the step in the RRD files is fixed when they are originally
generated, and if you change the step parameter afterwards, you'll
have to delete the old RRD files or somehow convert them. (This
variable is only applicable if the variable 'concurrentprobes' is
set in the 'General' section.)
Example value: 300
timeout
The fping "-t" parameter, but in (possibly fractional) seconds
rather than milliseconds, for consistency with other Smokeping
probes. Note that as Smokeping uses the fping 'counting' mode (-C),
this apparently only affects the last ping.
Example value: 1.5
tos Set the type of service (TOS) of outgoing ICMP packets. You need
at laeast fping-2.4b2_to3-ipv6 for this to work. Find a copy on
www.smokeping.org/pub.
Example value: 0x20
usestdout
Listen for FPing output on stdout instead of stderr ... (version
3.3+ sends its statistics on stdout).
Example value: true
AUTHORS
Tobias Oetiker <tobi@oetiker.ch>
Niko Tyni <ntyni@iki.fi>
SEE ALSO
Smokeping::probes::FPing(3)
2.8.0 2021-08-11 Smokeping_probes_FPing6(3)
smokeping 2.8.0 - Generated Wed Aug 11 10:09:25 CDT 2021