manpagez: man pages & more
info gnuplot
Home | html | info | man
[ << ] [ < ] [ Up ] [ > ] [ >> ]         [Top] [Contents] [Index] [ ? ]

3.25.23.2 format specifiers

The acceptable formats (if not in time/date mode) are:

      Format       Explanation
      %f           floating point notation
      %e or %E     exponential notation; an "e" or "E" before the power
      %g or %G     the shorter of %e (or %E) and %f
      %x or %X     hex
      %o or %O     octal
      %t           mantissa to base 10
      %l           mantissa to base of current logscale
      %s           mantissa to base of current logscale; scientific power
      %T           power to base 10
      %L           power to base of current logscale
      %S           scientific power
      %c           character replacement for scientific power
      %b           mantissa of ISO/IEC 80000 notation (ki, Mi, Gi, Ti, Pi, Ei, Zi, Yi) 
      %B           prefix of ISO/IEC 80000 notation (ki, Mi, Gi, Ti, Pi, Ei, Zi, Yi) 
      %P           multiple of pi

A ’scientific’ power is one such that the exponent is a multiple of three. Character replacement of scientific powers (‘"%c"‘) has been implemented for powers in the range -18 to +18. For numbers outside of this range the format reverts to exponential.

Other acceptable modifiers (which come after the "%" but before the format specifier) are "-", which left-justifies the number; "+", which forces all numbers to be explicitly signed; " " (a space), which makes positive numbers have a space in front of them where negative numbers have "-"; "#", which places a decimal point after floats that have only zeroes following the decimal point; a positive integer, which defines the field width; "0" (the digit, not the letter) immediately preceding the field width, which indicates that leading zeroes are to be used instead of leading blanks; and a decimal point followed by a non-negative integer, which defines the precision (the minimum number of digits of an integer, or the number of digits following the decimal point of a float).

Some systems may not support all of these modifiers but may also support others; in case of doubt, check the appropriate documentation and then experiment.

Examples:

      set format y "%t"; set ytics (5,10)          # "5.0" and "1.0"
      set format y "%s"; set ytics (500,1000)      # "500" and "1.0"
      set format y "%+-12.3f"; set ytics(12345)    # "+12345.000  "
      set format y "%.2t*10^%+03T"; set ytic(12345)# "1.23*10^+04"
      set format y "%s*10^{%S}"; set ytic(12345)   # "12.345*10^{3}"
      set format y "%s %cg"; set ytic(12345)       # "12.345 kg"
      set format y "%.0P pi"; set ytic(6.283185)   # "2 pi"
      set format y "%.0f%%"; set ytic(50)          # "50%"

      set log y 2; set format y '%l'; set ytics (1,2,3)
      #displays "1.0", "1.0" and "1.5" (since 3 is 1.5 * 2^1)

There are some problem cases that arise when numbers like 9.999 are printed with a format that requires both rounding and a power.

If the data type for the axis is time/date, the format string must contain valid codes for the ’strftime’ function (outside of ‘gnuplot‘, type "man strftime"). See timefmt for a list of the allowed input format codes.


[ << ] [ < ] [ Up ] [ > ] [ >> ]         [Top] [Contents] [Index] [ ? ]

This document was generated on February 28, 2014 using texi2html 5.0.

© manpagez.com 2000-2024
Individual documents may contain additional copyright information.